Install vinyl siding garage

When you install the vinyl siding onto your detached garage, you need to use a strip of metal known as a starter strip. The starter strip material is sold in a variety of different thicknesses. By purchasing the thickest starter strip material that is available, you can install your new vinyl siding as close to the ground as possible. Being close to the ground will help to protect the structure from damage caused by pest and moisture intrusion.

Tip: To ensure that your garage's siding is straight and level, use a chalk line to mark where you need to attach the starter strip to the garage's walls. When you reach the top row of the siding on your new garage, attach it as close to the soffits as you possibly can and then top it with a sill trim strip.

The sill trim strips along the top of the siding will help to hide the attachment strips for the siding, and they will help to keep water from leaking behind the vinyl siding and damaging the underlying wood structure of your garage.

Finally, if you do not feel comfortable installing the vinyl siding on your home's new detached garage yourself, then you should enlist the help of a professional building contractor in your local area.

This is a straightforward project for them to complete and is something that shouldn't be too expensive. Siding goes up very quickly and achieves a nice finished look for your new garage. For more information, contact a business such as Leger Siding. Basic guidelines for vinyl siding installation.

Spanish version and French version also available. Understand the codes and compliance requirements for properly installing polymeric products in high-wind regions with this at-a-glance guide.

Toggle navigation. Vinyl Siding Installation. Spanish Version. Getting Started. Sheathing Nailability Vinyl siding can be installed over common wood sheathings such as plywood, oriented strand board OSB , or other materials e. Water-resistive Barrier Vinyl siding should be installed over a continuous water-resistive barrier to stop the intrusion of incidental water.

Flashing Code-compliant flashing should be integrated with the water-resistive barrier and applied around windows, doors, and other openings. How to Measure Estimating Required Materials All houses can be broken down into shapes of rectangles or triangles, or a combination of both.

The area to be sided can be determined by measuring the height and width of the house, including windows Fig. Total all of the measurements for the areas to be sided.

Windows and doors are not usually deducted. Including them will provide an allowance factor for waste. If the windows and doors are extremely large such as a garage or sliding glass doors , some deductions can be made Fig. To estimate the amount of starter strip required, measure the linear feet around the entire base of the house. Add siding to all material estimates to allow for waste, depending on the pitch of the roof and other house-specific factors.

To estimate the total pounds of fasteners required, multiply the total square feet of siding by 0. Every square feet 9. A: B:. C: D:. Estimating Worksheet Download the estimating worksheet here. Fastener Choices Use aluminum, galvanized steel, or other corrosion-resistant nails, staples, or screws when installing vinyl siding.

Whether using a nail, screw, or staple to fasten the siding, the following basic rules must be followed: Make sure the panels are fully locked along the length of the bottom, but do not force them up tight when fastening. Do not drive the head of the fastener tightly against the siding nail hem. Tight nailing, screwing, or stapling will cause the vinyl siding to buckle with changes in temperature Fig.

When fastening, start in the center of the panel and work toward the ends. Center the fasteners in the slots to permit expansion and contraction of the siding Fig. Drive fasteners straight and level to prevent distortion and buckling of the panel Fig.

These distances may be increased if the manufacturer permits greater spacing based on wind load testing. Start fastening vertical siding and corner posts in the top of the uppermost slots to hold them in position Fig.

Place all other fasteners in the center of the slots. Screw Fasteners Screw fasteners can be used if the screws do not restrict the normal expansion and contraction movement of the vinyl siding panel on the wall. Cutting the Siding When cutting vinyl siding or soffit, follow these guidelines: Safety goggles are always recommended for all cutting and nailing operations. Push each panel into the J-channel. Once the J-channel is installed and the soffit pieces are cut, you will be able install them.

You can do this by pressing the soffit pieces into the channel, bending them to fit if necessary vinyl siding is quite flexible. If you're having difficulty just pressing them in, you may need to pull the channel lip back with a pry bar or locking tool to get the siding panels to fit.

Slide in the fascia siding pieces. Secure the top edge of the fascia pieces with galvanized or painted nails placed every couple of feet. Reattach the gutters. Part 3. Measure the walls. Measure the length of the walls from the eaves to the bottom of any existing siding. This will help you to figure out how many panels of siding you'll need per wall.

Divide the length of each wall by 8 inches the width of a piece of siding. If the result is a whole number, you're in luck: you'll be able to install the pieces of siding without leaving any gaps or needing to cut any pieces to size. But if the result is not a whole number, you will need to cut the final piece of siding lengthwise in order to fill in the remaining space.

If you have to cut the last row of siding, you'll need to use a length of J-channel on the top edge of the siding instead of utility trim. Install a starter strip. Attach the starter strip to the plywood, but don't nail it so tightly that it will restrict the strip's movement. Install the corner posts. Make sure the corner siding pieces are completely straight before you secure them.

Once you're satisfied, nail them to the adjoining walls, working from top to bottom. Install J-channel around windows and doors.

The next step is to install J-channel around all four sides of exterior doors and windows. Begin installing the wall siding. Apply any necessary insulation materials to the walls before you begin to install the siding. Slide the bottom row of panels into place, making sure to hook the bottom lip of each panel under the starting strip. Secure the panels with a nail every 16 inches Overlap adjoining panels.

When joining two lengths of siding together, overlap them by about 1 inch When deciding which side to overlap on, choose the side that will be least obvious from the front or most used area of your house. For example, if your driveway is located to the right of your house, then a right over left overlap will be least noticeable. Install siding around windows. When you get to a window, you will need to cut sections from the panels directly above and below it to fit.

Measure the width of the piece you need to cut by holding the length of siding against the window and marking the edge points on the panel with a pencil. Transfer this measurement onto the piece of siding. Make the vertical cuts on the siding panel with a saw and make the horizontal cut with a utility knife, then snap out the piece. Install the cut pieces of siding above and below the windows, as normal.

Install the top row of siding. When you reach the top row of siding, you will need to measure and cut it to fit. When you cut the top siding panel to the appropriate height you will be removing the nailing strip. Use a snap-lock punch tool to punch the top edge of the panel along 6 inch Slot the bottom edge of the panel into the panel below and slide the top edge under the under-sill trim.

The raised slots you made with the snap-lock punch will catch onto the trim and hold the top siding panel firmly in place -- so there is no need to face nail it to secure. Can a pneumatic roofing gun be used for siding? I realize the nails are not to be tight to the wall, but that can be adjusted with the gun. Is this a common practice? In theory it's possible, but it would be to cumbersome and you would have to get the air pressure just right. It's not recommended. Not Helpful 5 Helpful 6.

Use foam insulation and bend the trim. Attach it to a board to secure it using liquid nails. Not Helpful 12 Helpful 9. How do I install vinyl siding when both sides of a wall must join at a level point? Use a story pole. Mark the exposure of the siding on a 1x3-inch furring strip; now you can walk around and see where all the siding will fall and what works best. Then put in the starter strip level. Not Helpful 2 Helpful 2.